FIZIK IÇIN SENSÖRLER

The Differential Voltage sensor (1022539) is designed for measuring voltages in the range between -10 and +10 V. With a wide input voltage range this sensor can be used to measure voltages in AC and DC circuits. The sensor has differential ... more

Thermocouple Sensor The thermocouple sensor is capable of measuring temperatures in two ranges: -200 to 1300 °C (wide range) and -20 to 110 °C (narrow range) The desired range is selected by a switch integrated on ... more

Serbest durumda zaman ölçümü, yol deneyleri, sarkaç salınımları ve impuls sayımı için 3B NETlog (1000540/1000539) veya dijital sayacın (1001033/1001032) kumandasına yönelik kızılötesi fotosel. B ... more

Bant üzerindeki bir vagonun bir mesafeyi kat etmesi için gereken zamanın ya da ışık sensorlarının önünü kapattığı sürenin güvenilir bir şekilde ölçülmesi için bir ya da iki ışık ... more

Fotoselin (1000563) veya lazer tepkime sensörünün (1001034) harici bir dijital sayaçta kullanılmasına yönelik bağlantı kutusu. 12 V AC adaptör dahildir. Giriş: 8 pimli miniDIN yuva Çıkış: iki 4 mm g ... more

The relative pressure sensor FW is used to measure relative pressures. The sensor is equipped with two measuring chambers via whose terminals pressure diff erences can be measured. Range: 0 − ±1000 hPa Accuracy: ± ... more

Displacement sensor FW is used to record periodic / oscillating movements which can be registered via a cord on the cord roller. The sensor has a rotating cord roller and a built-in precision potentiometer. Wheel: 24 mm Ø Maximum ... more

Magnetic field sensor FW ± 2000 mT is used to measure magnetic flux density in the tangential direction. Located on the tip of the probe is a Hall sensor with an output signal proportional to the operating voltage. The sensor is equipped ... more

Temperature sensor for the measurement of temperatures on the copper tubing of a heat pump (P-1000819 / P-1000820). Temperature sensor shaft made of rust-proof stainless steel. Tip with matching copper terminal. Can be used in conjunction ... more

Motion detector (for WiLab and VinciLab) The Motion detector BT55i is a sonar device that emits ultrasonic pulses, which reflect off an object. The sensor measures the time it takes an ultrasonic pulse to travel from the sensor to the object ... more

This Current Sensor is specially designed for measurements of very low and accurate currents. It can be used in various experiments such as: • characteristics of a light bulb and a diode, • measurements of internal resonance ... more

Magnetic field sensor FW ± 2000 mT is used to measure magnetic flux density in the axial and tangential directions. Located on the tip of the probe is a Hall sensor with an output signal proportional to the operating voltage. The ... more

The thermocouple sensor 0135i measures temperatures in two ranges, which can be selected using the switch. The sensor uses a thermocouple type K, which consists of Chromega and Alomega wires that are welded together to form a measuring junction ... more

The UVA sensor 0388 measures the intensity of ultraviolet radiation. This sensor consists of a broadband UV sensitive silicon photodiode and responds primarily to UVA radiation. Range: 320 ... 390 nm Resolution (12-bit): 5 mW/m² Can be used ... more

The light sensor 0513 measures light intensity and is sensitive to the visible light spectrum and also infrared. Because of its range the sensor is suitable for measurements in normal indoor situations. Range: 0.1 ... 10 W/m² ... more

The Voltage sensor BT02 is a low-cost, generic sensor that measures voltage. This sensor has a direct connection to the inputs of a measurement interface. It has two 4-mm plugs for easy connection. Range: -10 ... +10 V. Resolution ... more

The temperature sensor BT05i is a low-cost, general-purpose temperature sensor that can be used to measure temperature in the range of -40°C to 150°C, in liquids (water, mild acidic solutions) and air. The sensing element of the ... more

The conductivity sensor BT27i measures the ability of a solution to conduct an electric current between two electrodes. The conductivity sensor consists of a conductivity electrode and an amplifier. The sensor has three measurement ranges ... more

The Voltage sensor BT32i is designed for measuring voltages between -500 and +500 mV. The sensor has diff erential inputs; measurements can be done directly across circuit elements without the constraints of common grounding. It has two ... more

The Force sensor BT42i measures pushing and pulling forces. It uses strain gauge technology. The sensor has two measurement ranges, which can be selected using a switch. Range: -5 ... 5N, -50 ... 50 N. Resolution (12-bit): 0.003 N ... more

The light sensor BT50i measures light intensity and has three measurement ranges, which can be selected using a switch. Because of its ranges the sensor is suitable as well for indoor as for outdoor measurements. Full sun illumination is ... more

 The pressure sensor BT66i is designed to measure absolute gas pressure. The pressure is measured via a pressure valve, which is located on the side of the box. The sensor has two measurement ranges, which can be selected using a switch ... more

The radiation sensor BT70i detects alpha, beta and gamma ionizing radiation. The sensor outputs a pulse when decay is detected. Also, a clicking sound is emitted and a LED light flashes. The sensor is suitable to detect low-level radiation ... more

The humidity sensor BT72i measures relative humidity. The sensor consists of an integrated circuit, which uses a capacitive polymer to sense humidity. The holes in the sensor box provide air circulation. Range: 0 ... 100 % Resolution ... more

The sound sensor BT80i consists of a microphone followed by an internal amplifier. It measures variations in air pressure caused by sound waves. Because of the high sensitivity, the sensor is very much suited to detect pressure pulses. The ... more