CIRCUITS

Complete equipment for recording charging and discharging curves for capacitors at individual points. Includes 12 V AC plug-in power supply. The charger and discharger consists of three units in a single housing: a voltage comparator, a digital ... more

Metal stem with knurled screw and 4 mm bore hole on acrylic rod, as insulated holder for wires, e.g. when conducting experiments on the optical bench are performed. Diameter: approx. 10 mm Length: approx. 100 mm more

Replica of Alessandro Volta’s apparatus consisting of series-connected galvanic cells to make up a source of electricity. Zinc and copper plates stacked in alternation on top of each other are separated in each case by a piece of felt ... more

Switch attached to a safe box for building simple electric circuits using safety experiment leads. Printed with a circuit symbol. Maximum voltage: 12 V Maximum current: 5 A Dimensions: 135x85x40 mm³ more

Normally open push-button switch attached to a safe box for building simple electric circuits using safety experiment leads. Printed with a circuit symbol. Maximum voltage: 12 V Maximum current: 2 A Dimensions: 135x85x40 mm³ more

Knife-edge switch attached to a safe box for building simple electric circuits using safety experiment leads. Printed with a circuit symbol. Maximum voltage: 12 V Maximum current: 5 A Dimensions: 135x85x40 mm³ more

Fuse holder attached to a safe box for building simple electric circuits using safety experiment leads. Printed with a circuit symbol. Fuses (not included):           20 mm x 5 mm diam. Maximum voltage:                12 V Maximum current ... more

Pair of crocodile clips for connecting loose resistors and other electronic components or samples from the “Conductors and Non-Conductors” set. Attached to a safe box for building simple electric circuits using safety experiment leads. Printed ... more

Universal holder for two-pole components (resistors, capacitors, diodes, LEDs) attached to a safe box for building simple electric circuits using safety experiment leads. Printed with a circuit symbol. Dimensions: 135x85x40 mm³ more

1N4002 semiconductor in an electrically safe box for assembling simple electric circuits using safety experiment leads. Featuring printed circuit symbol. Maximum voltage: 12 V Maximum current: 1 mA Dimensions: 135x85x40 mm³ more

Low-voltage motor with pulley for simple experiments on mechanical and electrical energy. The relationship between current direction and direction of rotation is immediately obvious. Built onto an electrically safe box for assembling simple ... more

LED on an electrically safe box for assembling simple electric circuits using safety experiment leads. Featuring built-in current limiting resistor and printed circuit symbol. Maximum voltage: 12 V Maximum current: 20 mA Dimensions: 135x85x40 ... more

LED on an electrically safe box for assembling simple electric circuits using safety experiment leads. Featuring built-in current limiting resistor and printed circuit symbol. Maximum voltage: 12 V Maximum current: 20 mA Dimensions: 135x85x40 ... more

Battery holder in an electrically safe box for assembling simple electric circuits using safety experiment leads. Printed circuit symbol and battery direction. Batteries not included. Battery: 4.5 V, 3R12, flat battery Dimensions: 135x85x40 ... more

600-winding coil without core attached to a safe box and featuring safety sockets. For experiments on induction, a bar magnet can be passed through the coil. Dimensions: 135x85x40 mm³ more

Single-pole double-throw change-over switch attached to a safe box for building simple electric circuits using safety experiment leads. Printed with a circuit symbol. Maximum voltage: 12 V Maximum current: 5 A Dimensions: 135x85x40 mm³ ... more

Bridge rectifier circuit consisting of four semiconductor diodes connected in Graetz configuration. Inside a safe box for building simple electric circuits using safety experiment leads. Printed with circuit symbols. Maximum voltage: 12 V ... more

Bridge rectifier circuit consisting of four LEDs connected in Graetz configuration. Inside a safe box for building simple electric circuits using safety experiment leads. Printed with circuit symbols. Maximum voltage: 12 V Maximum current ... more

Circuit comprised of two LEDs for indicating the direction of current. Inside a safe box with sockets for safety experiment leads. Printed with circuit symbols. Maximum voltage: 12 V Maximum current: 20 mA Dimensions: 135x85x40 mm³ more

Classic set-up for verifying Ohm’s law for a two-pole resistor. Inside a safe box with sockets for safety experiment leads. Printed with circuit symbols. Maximum voltage: 12 V Maximum current: 2 A Dimensions: 135x85x40 mm³ more

Four unknown resistors which can be connected separately in two series circuits. Inside a safe box with sockets for safety experiment leads. Printed with circuit symbols. Maximum voltage: 6 V Maximum current: 200 mA Dimensions: 135x85x40 ... more

In plastic housing with 4-mm safety plugs. Specifications: Dimensions: 122x70x50 mm Resistance: 1 Ω Tolerance: 1% Load rating: 4 W more

In plastic housing with 4-mm safety plugs. Specifications: Dimensions: 122x70x50 mm Resistance: 10 Ω Tolerance: 1% Load rating: 4 W more

In plastic housing with 4-mm safety plugs. Specifications: Dimensions: 122x70x50 mm Resistance: 100 Ω Tolerance: 1% Load rating: 4 W more

In plastic housing with 4-mm safety plugs. Specifications: Dimensions: 122x70x50 mm Resistance: 1 kΩ Tolerance: 1% Load rating: 1 W more